Allied Telesis Power Supply AT PWR14 User Manual

Related Documents  
Installing the AT-PWR14 Power Supply  
This installation guide is an abbreviated version of the installation procedure.  
For details on the components, features, and functions of this product, refer to  
the following documents on our web site, www.alliedtelesis.com:  
To install the AT-PWR14, perform the following procedure:  
1. Unpack the new AT-PWR14 module from its shipping container and store  
the package material in a safe location.  
AT-CV5000 Media Converter Chassis Installation Guide  
Note  
(PN 613-50580-00)  
You must use the original shipping material if you need to return the  
power supply module to Allied Telesis.  
AT-S70 Management Software User’s Guide (PN 613-50617-00)  
Package Contents  
Make sure the following items are included in the shipping package. If any  
item is missing or damaged, contact your Allied Telesis sales representative  
for assistance.  
2. Select the power supply slot in the AT-CV5000 chassis where you want to  
install the AT-PWR14 power supply.  
CONVERTEONFamily  
AT-PWR14 Redundant Power Supply (AC)  
3. Make sure that the power switch is in the OFF position.  
One AT-PWR14 Redundant Power Supply (AC)  
This Installation Guide  
4. Loosen the two captive screws that secure the blank slot cover  
(AT-CV5PNL2) of the selected power supply slot, and remove the blank  
slot cover, as shown in Figure 3.  
Installation Guide  
Warranty Card  
Locations of the Power Supply Slots  
A
Figure 2 illustrates the locations of the two power supply modules at the rear  
of an AT-CV5000 AC model chassis.  
Allied Telesis, Inc.  
A
100-240V  
A
C
 N
~
W
AR  
T
h
N
it  
th  
IN  
is  
mG  
u
n
re  
d
u
ig  
c
e
h
k
s
t
h
av  
o
in  
e
p
u
ri  
e
ts  
s
m
o
b
re  
e
f
t
h
s
.
fo  
e
re  
le  
c
a
n
h
o
tr  
ic  
o
n
e
rv  
e
d
is  
ic  
p
c
in  
o
o
g
ck  
w
n
e
e
u
,
r
n
in  
p
it  
u
n
t.  
To  
w
c
t
a
ll  
p
o
e
r
A
B
A
B
100-240VAC~  
100-240VAC~  
AT-PWR14  
Overview  
211  
POWER  
FAULT  
The AT-PWR14, shown in Figure 1, is an AC redundant power supply (RPS)  
used with the AT-CV5000 chassis only. When installed, the module operates  
in a standby mode. If the standard power supply fails or loses power, the AT-  
PWR14 module changes from standby to active and provides all power to the  
system to prevent a network failure.  
Figure 3. Removing the Power Supply Slot Cover  
214  
5. Remove the AT-PWR14 module from its shipping package.  
PS SLOT A - Primary  
PS SLOT B - Redundant  
6. Slide the AT-PWR14 module into the RPS slot, as shown in Figure 4.  
Figure 2. Locations of the Power Supply Slots on the Rear Panel of  
an AT-CV5000 AC Model Chassis  
A
A
Before installing a power supply, please note the following guidelines:  
W
A
R
u
N
Th  
IN  
mG  
is  
ni  
re  
t
du  
ig  
ce  
ht  
h
av  
th  
in  
e
e
pu  
ri  
m
ct  
ts  
sk  
or  
e
b
ef  
o
f
e
th  
or  
le  
an  
ne  
e
se  
rv  
ri  
o
c
ic  
sh  
oc  
p
ow  
is  
co  
nn  
in  
g
k,  
er  
in  
ec  
un  
d
it.  
pu  
t.  
a
ll  
T
o
w
t
po  
er  
Note  
The AT-CV5000 chassis comes with two slots designated for the power  
supplies; however, it is shipped with one standard power supply  
preinstalled and one empty slot for an optional power supply. The  
redundant power supply can be ordered separately from your ATI sales  
representative.  
A
T-PW  
R14  
PO  
FA  
WER  
U
LT  
AT-PWR14  
PO  
W
ER  
209  
FA  
U
LT  
Figure 4. Inserting the AT-PWR14 Module into the Power Supply Slot  
208  
7. Secure the AT-PWR14 module to the AT-CV5000 chassis by using a  
Phillips screwdriver to tighten the captive screws, as shown in Figure 5.  
Note  
Figure 1. AT-PWR14 Power Supply Module  
Make sure that both power supplies (primary and redundant) are rated for  
the same power ratings. For information on the power supply module,  
refer to the documentation that is shipped with the module.  
Note  
A
The power supply is hot-swappable. You can install it without powering  
OFF the AT-CV5000 chassis.  
A
1
0
0
-2  
4
0
V
A
 V
C
~
W
A
R
u
N
Th  
IN  
mG  
is  
ni  
re  
t
du  
ig  
ce  
ts  
ht  
h
av  
o
th  
in  
e
e
pu  
ri  
m
ct  
sk  
or  
e
th  
ric  
it.  
b
ef  
f
e
or  
le  
an  
ne  
ck  
e
s
o
,
er  
vi  
s
ho  
p
ow  
er  
is  
co  
cin  
g
un  
d
in  
pu  
nn  
ec  
t.  
po  
T
o
w
t
a
ll  
er  
AT-PWR1  
Note  
PO  
FA  
4
WER  
U
L
T
The AT-PWR14 power supply can be installed in either one of the power  
supply expansion slots while the converter chassis is powered ON. You  
do not need to power OFF the chassis to install the power supply.  
212  
Figure 5. Securing the AT-PWR14 Module  
3
*613-50585-00 Rev C*  
613-50585-00 Rev C  
1
2
 
       

3Com Home Security System 1000BASE T GBIC User Manual
Addonics Technologies Blu ray Player DDU7SAS User Manual
Agilent Technologies Computer Hardware 37907A User Manual
Alpine CD Player 68 04123Z09 A User Manual
Alpine CD Player CDE 9843 User Manual
Amana Range W10130752B User Manual
American Standard Indoor Furnishings 0031000 User Manual
Atlas Sound Switch AA PPRC User Manual
Avenview TV Cables HDM C5 3X SET User Manual
Axis Communications Security Camera axis fixed dome network camera User Manual