Altec Lansing Stereo System IMT800 User Manual

Altec Lansing Mix Portable Speaker  
®
for iPhone and iPod  
iMT800  
User Guide  
 
Safety Information  
The lightning flash with arrowhead, within an equilateral triangle, is  
intended to alert the user to the presence of uninsulated “dangerous  
voltage” within the products enclosure that may be of sufficient  
magnitude to constitute a risk of electric shock to persons.  
Caution: To prevent the risk of electric shock, do not remove cover  
(or back). No user-serviceable parts inside. Refer servicing to  
qualified service personnel.  
The exclamation point within an equilateral triangle is intended  
to alert the user to the presence of important operating  
and maintenance (servicing) instructions in the literature  
accompanying the appliance.  
BATTerieS  
7. Do not block any ventilation openings. Install in accordance with the manufacturers  
instructions.  
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the  
same or equivalent type. Do not expose to excessive heat such as sunshine, fire, or  
the like. The battery used in this product must be properly recycled or disposed of.  
Instructions for removing the battery can be found in the Quick Start Guide. Please  
contact your local recycling center for proper battery handling and disposal instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or  
other apparatus (including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A  
polarized plug has two blades with one wider than the other. A grounding type plug  
has two blades and a third grounding prong. The wide blade or the third prong are  
provided for your safety. If the provided plug does not fit into your outlet, consult an  
electrician for the replacement of the obsolete outlet.  
Power SoUrce  
Use only power supplies of the type specified in the operating instructions or as marked  
on the appliance. If a separate power supply is included with this apparatus, do not  
substitute with any other power supply – use only manufacturer-provided power supplies.  
10. Protect the power cord from being walked on or pinched particularly at plugs,  
convenience receptacles, and the point where they exit from the apparatus.  
cAUTioN  
11. Only use attachments/accessories specified by the manufacturer.  
To prevent electric shock do not use this (polarized) plug with an extension cord,  
receptacle or other outlet unless the blades can be fully inserted to prevent blade  
exposure.  
12.  
Use only with the cart, stand, tripod, bracket, or table specified by the  
manufacturer or sold with the apparatus. When a cart is used, use  
caution when moving the cart/apparatus combination to avoid injury  
from tip-over.  
wArNiNG  
To reduce the risk of fire or electric shock, do not expose this appliance to rain  
or moisture.  
13. Unplug this apparatus during lightning storms or when unused for long periods  
of time.  
iMPorTANT SAFeTY iNSTrUcTioNS  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
14. Refer all servicing to qualified service personnel. Servicing is required when the  
apparatus has been damaged in any way, such as power-supply cord or plug is  
damaged, liquid has been spilled or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture, does not operate normally, or  
has been dropped.  
4. Follow all instructions.  
15. Do not install in an area which impedes the access to the power plug. Disconnecting  
the power plug is the only way to completely remove power to the product and must  
be readily accessible at all times.  
5. Do not use this apparatus near water. This apparatus shall not be exposed to  
dripping or splashing, and no objects filled with liquids, such as vases, shall be  
placed on the apparatus.  
6. Clean only with dry cloth.  
1
 
Contents  
Welcome............................................................................................................................................................................................................................... ii  
Safety Information................................................................................................................................................................................................................1  
Package Contents................................................................................................................................................................................................................3  
Getting Started.....................................................................................................................................................................................................................4  
Placing and Removing Adapters for the iPhone and iPod...................................................................................................................................................5  
Speaker Features and Indicators .........................................................................................................................................................................................6  
Speaker Controls..................................................................................................................................................................................................................7  
Clip-On Remote Features.....................................................................................................................................................................................................9  
Listening to Your iPhone or iPod........................................................................................................................................................................................11  
Setting EQ Controls............................................................................................................................................................................................................13  
Charging your iPhone or iPod ............................................................................................................................................................................................15  
Listening to the FM Radio ..................................................................................................................................................................................................15  
Listening to Additional iPhone, iPod, Non-Docking iPod or Other Audio Devices ............................................................................................................16  
Personalizing the Power-On Message ...............................................................................................................................................................................17  
Maintaining Your Speaker System .....................................................................................................................................................................................17  
Troubleshooting..................................................................................................................................................................................................................18  
Warranty .............................................................................................................................................................................................................................21  
2
 
Package Contents  
Altec Lansing Mix speaker system  
Clip-on remote  
Miscellaneous adapters  
for iPhone and iPod  
AC adapter  
Two 3.5 mm stereo cables  
3
 
Getting Started  
How to install the Ac Adapter  
5
Replace the battery door.  
1
Connect the AC adapter cable plug  
into the speaker system’s jack.  
NoTe Please discard used batteries properly.  
NoTe When you are finished listening to your portable audio device,  
please remember to turn both it and your speaker system off to conserve  
electricity.  
The jack is located on the back of the  
system.  
2
Plug the AC adapter into the wall  
outlet.  
How to install the clip-on remote Battery  
The clip-on remote battery (included) is not installed at the factory. To install  
the battery, follow the steps below. The battery compartment is at the back  
of the remote. Push the battery compartment door in the direction of the  
arrow to unlock it.  
How to install the Speaker Batteries  
Your Altec Lansing Mix speaker system can also be powered by 8 D-size  
(LR20) batteries (not included). To install the batteries, follow the steps below:  
1
Make sure that there is no iPhone  
or iPod in the system’s dock  
and that no other devices are  
connected to the system.  
1
Open the battery door.  
The battery door is located on the back  
of the remote. Using your thumb, push  
the battery door toward the carabiner  
clip. Then lift the battery door open.  
2
3
Unplug the AC adapter from the  
Mix speaker system.  
2
3
Position the battery (included) so it  
sits in the battery holder correctly.  
Open the battery compartment.  
The battery door is located on the  
Make sure the polarity (the + and – sides of the battery) is correct.  
bottom of the Mix speaker system. To access it, place the unit on its  
back, so that the speakers are facing the ceiling. Then simply pull the  
tabs to open the battery compartment.  
Replace the battery door.  
NoTe Please discard used batteries properly.  
Caution: Do not place the unit on its top side. This may damage the  
volume knob.  
4
Install 8 D-size (LR20) batteries (not included) in the battery  
compartment.  
Make sure the batteries are correctly installed as illustrated in the  
battery compartment. The batteries will provide up to 30 hours of  
continuous playing time.  
4
 
Placing and Removing Adapters for the iPhone and iPod  
Your Altec Lansing Mix speaker system includes removable adapters for  
todays popular iPhone and iPod models. These adapters ensure that your  
iPhone and iPod properly fit in the speaker systems dock. As new iPhone  
and iPod models are introduced, new adapters will be made available to  
customers. You may also use the adapter supplied with your iPhone or  
How to Place an Adapter  
1
Select the correct adapter for your  
iPhone or iPod.  
Using the correct adapter ensures a  
proper fit for your iPhone or iPod.  
2
Gently press the iPhone or iPod  
adapter into the dock.  
Now you can carefully place your  
iPhone or iPod into the dock.  
NoTe Your iPhone or iPod cannot be in  
a case.  
How to remove an Adapter  
1
2
Remove your iPhone or iPod.  
Grip the adapter and pull gently upward.  
5
 
Speaker Features and Indicators  
Power/volume increase/  
volume decrease knob  
Track back button  
EQ button  
Track forward button  
Source button  
FM antenna  
Two AUX jacks  
LCD display  
Battery indicator  
FM stereo indicator  
AC adapter jack  
Guard for iPhone or iPod  
Universal docking station for iPhone or iPod  
6
 
Speaker Controls  
Ensure the AC adapter is connected to the system and plugged into the wall. See the Getting Started  
section for more information. Press the knob.  
Turn on your speaker system  
Press the knob. Whenever you are finished using your speaker system, please remember to turn it and  
your iPhone, iPod or other MP3 player off to conserve electricity.  
Turn off your speaker system  
Change audio source  
Press the “SOURCE” button to cycle through and select the audio source: iPod, FM radio, AUX 1 or AUX 2.  
See the Setting EQ Controls section for specific information on selecting EQ presets and adjusting the  
7-band graphic EQ.  
Set the graphic equalizer  
Turn up the volume  
Rotate the knob clockwise.  
Turn down the volume  
Rotate the knob counter-clockwise.  
Skip to the beginning of the current song on  
your iPhone or iPod  
In “iPod” mode, press the button.  
In “iPod” mode, press and hold the button.  
In “iPod” mode, press the button.  
Rewind the currently playing track on your  
iPhone or iPod  
Skip to the beginning of the next song on  
your iPhone or iPod  
Fast-forward the currently playing track on  
your iPhone or iPod  
In “iPod” mode, press and hold the button.  
Tune radio stations  
In “FM” mode, use the and buttons. See the Listening to the Radio section for additional information.  
7
 
Speaker Controls  
In “FM” mode, press and hold the or button. See the Listening to the Radio section for additional  
information.  
Scan radio stations  
Listen to an additional iPhone, iPod, non-  
docking iPod or other portable audio device  
See the Listening to Additional iPhone, iPod, Non-Docking iPod or Other Portable Audio Devices section  
for specific information on using devices attached to your speaker systems AUX jacks.  
Enter a personalized power-on message  
Reset all settings  
See the Personalizing the Power-On Message section for specific information on using this feature.  
With the speaker system turned on, press the and buttons simultaneously for a few seconds. Once  
the word “RESET ?” is displayed on the screen, press the button to reset all settings.  
Reset all settings (see above), and use the and buttons to select the region closest to you (“REGION  
1: USA,” “REGION 2: EUROPE/ASIA,” “REGION 3: JAPAN WIDE” or “REGION 4: JAPAN”). Then, press  
the knob to save your selection.  
Select FM Band region  
Check battery status  
If the Mix is being powered by batteries, you can see how much battery power you have left. Press and  
hold the “SOURCE” button to display the amount of battery power remaining and press it again to exit  
this mode. The unit will automatically exit this mode after a few seconds.  
8
 
Clip-On Remote Features  
The clip-on remote lets you operate many functions of your Altec Lansing Mix  
speaker system:  
Turn on your speaker system  
Turn off your speaker system  
Press the button.  
Press the button.  
Source button  
Power on/off button  
Volume decrease  
button  
Volume increase  
button  
Press the “SOURCE” button to cycle  
through and select the audio source:  
iPod, FM radio, AUX 1 or AUX 2.  
Change audio source  
Track back button  
EQ button  
Track forward button  
Play/pause button  
Turn up the volume  
Press the “+” button.  
Press the “–” button.  
Turn down the volume  
Skip to the beginning of the current  
song on your iPhone or iPod  
In “iPod” mode, press the button.  
Rewind the currently playing  
track on your iPhone or iPod  
In “iPod” mode, press and hold the  
button.  
FM preset buttons  
FM preset buttons  
Skip to the beginning of the next  
song on your iPhone or iPod  
In “iPod” mode, press the button.  
Fast-forward the currently playing  
track on your iPhone or iPod  
In “iPod” mode, press and hold the  
button.  
Carabineer clip  
See the Setting EQ Controls section for  
specific information on selecting EQ presets  
and adjusting the 7-band graphic EQ.  
Set the graphic equalizer  
9
 
Clip-On Remote Features  
Play/pause a song on your iPhone or iPod  
Tune radio stations  
In “iPod” mode, press the button to begin playing a selected track. Press the button again  
to pause it.  
In “FM” mode, use the or buttons. See the Listening to the Radio section for additional  
information.  
In “FM” mode, press and hold the or button. See the Listening to the Radio section for  
additional information.  
Seek radio stations  
In “FM” mode, tune to the station you’d like to store, and then press and hold one of  
the PRESET buttons (P1, P2, P3 or P4). See the Listening to the Radio section for  
more information.  
Store a radio station  
In “FM” mode, press the PRESET button (P1, P2, P3 or P4) that corresponds to the station  
you’d like to hear. See the Listening to the Radio section for more information.  
Select a preset radio station  
NoTe For best results, aim the clip-on remote toward the Mix speaker system.  
10  
 
Listening to Your iPhone or iPod  
NoTe To conserve battery power, reduce the speaker system volume level.  
1
Dock your iPhone or iPod in the  
Altec Lansing Mix speaker system.  
NoTe During battery-only operation, the speaker system automatically  
shuts down if no audio is detected for a few minutes. This is to conserve  
battery power. Press the button on the speaker system or the button  
on the clip-on remote to turn the speaker system back on.  
Make sure the correct adapter for  
iPhone or iPod is inserted in the  
speaker systems dock. Slide the guard  
down to protect the iPhone or iPod.  
NoTe The speaker system is compatible with the alarm clock and sleep  
timer features built into select iPhone and iPod models. For these features  
to work properly, the speaker system must be connected to a wall outlet.  
When an iPhone or iPod is docked, the speaker system will not shut down  
automatically, enabling the alarm or sleep timer to play through the speaker  
system. See the user guide for iPhone or iPod for details on how to access  
these features.  
2
3
Select “iPod” mode.  
Press the “SOURCE” button on your  
speaker system or clip-on remote until the iPod icon appears on the  
LCD.  
Press the  
button on your iPhone, iPod, or clip-on remote.  
Music from your iPhone or iPod will start playing. The speaker system  
and the clip-on remote are capable of controlling basic functions of  
3rd-generation iPod models, the iPod touch, the iPod nano and the  
iPhone.  
NoTe During AC operation, if there is no iPhone or iPod docked and  
no audio input signal is detected for a few minutes, the speaker system  
automatically shuts down to conserve energy. Press the button on the  
speaker system or the button on the clip-on remote to turn the speaker  
system back on.  
4
5
Adjust the volume.  
Rotate the knob on the Altec Lansing speaker system to adjust the  
system volume. Or, use the “+”and “–” buttons on the clip-on remote.  
Find your desired song.  
Press the or button on your speaker system or clip-on remote to  
go to the next or previous track. Press and hold the or button on  
your speaker system or clip-on remote while the track is playing for  
high-speed forward or reverse music search of the current track.  
11  
 
Listening to Your iPhone or iPod  
How to Access Additional Features on Your iPhone or iPod Using  
the clip-on remote  
Press the P2 button once on the  
clip-on remote to advance to the next  
repeat mode:  
First, select “iPod” mode.  
• “Repeat 1” is displayed when the  
system is in the repeat one mode.  
• “Repeat” is displayed when the  
system is the repeat all mode.  
• “Repeat Off” is displayed when the  
repeat function has been turned off.  
Press the “SOURCE” button on your speaker system or clip-on remote until  
the iPod icon appears on the LCD.  
Repeat function  
Press the P1 button once on the  
clip-on remote to advance to the next  
shuffle mode:  
• “Shuffle S” is displayed when the  
system is in song shuffle mode.  
• “Shuffle A” is displayed when the  
Note: Use the P1 button on some  
older iPod models. Functionality may  
vary per iPhone or iPod model.  
Shuffle function  
system is in album shuffle mode.  
• “Shuffle Off” is displayed when the  
shuffling function has been turned  
off.  
Press the P3 button on the clip-on  
remote.  
Access the previous playlist  
Access the next playlist  
Press the P4 button on the clip-on  
remote.  
Note: Use the P2 button on some  
older iPod models. Functionality may  
vary per iPhone or iPod model.  
12  
 
Setting eQ Controls  
How to Set the Bass and Treble control Using the onboard controls  
5
exit the Treble Control screen.  
Press the “EQ” button again. Or the unit will automatically exit this  
screen after a few seconds.  
1
Access the bass and treble settings.  
Press the “EQ” button once. The Bass Control screen will appear on  
the LCD.  
How to change the eQ Presets Using the onboard controls  
2
3
4
5
Increase or decrease the bass level.  
1
2
Access the eQ presets.  
Rotate the knob.  
Press and hold the “EQ” button for approximately 3 seconds.  
enter the Treble Control screen.  
Select your desired preset.  
Press the EQ button again. The Treble Control screen will appear.  
Press the or buttons to cycle through the four EQ presets.  
Presets include: 1) ALTEC EQ, 2) ROCK, 3) HIP HOP, and 4) POP.  
Increase or decrease the treble level.  
Rotate the knob.  
3
exit the eQ Preset screen.  
exit the Treble Control screen.  
Press the “EQ” button again. Or the unit will automatically exit this  
screen after a few seconds.  
Press the “EQ” button again. Or the unit will automatically exit this  
screen after a few seconds.  
NoTe: To reset the EQ Presets to factory settings, press and hold the EQ  
button for a few seconds.  
How to Set the Bass and Treble control Using the clip-on remote  
1
Access the bass and treble settings.  
How to change the eQ Presets Using the clip-on remote  
Press the “EQ” button once. The Bass Control screen will appear on  
the LCD.  
1
2
Access the eQ presets.  
Press and hold the “EQ” button for approximately 3 seconds.  
2
3
4
Increase or decrease the bass level.  
Select your desired preset.  
Press the “+” or “–” buttons.  
Press the or buttons to cycle through the four EQ presets.  
Presets include: 1) ALTEC EQ, 2) ROCK, 3) HIP HOP, and 4) POP. Or,  
press P1 for ALTEC EQ, P2 for ROCK, P3 for HIP HOP or P4 for POP.  
enter the Treble Control screen.  
Press the “EQ” button again. The Treble Control screen will appear.  
3
exit the eQ Preset screen.  
Increase or decrease the treble level  
Press the “EQ” button again. Or the unit will automatically exit this  
screen after a few seconds.  
Press the “+” or “–” buttons.  
13  
 
Setting eQ Controls  
NoTe You can personalize the EQ presets by selecting a Preset EQ then  
pressing the “EQ” button twice to enter the Bass/Treble Control Mode.  
There you can make adjustments to the Preset EQs as described in the  
Bass and Treble Control sections. Changes are saved automatically.  
How to Adjust the 7-Band Graphic eQ Using the clip-on remote  
1
enter the Graphic eQ Mode.  
On the speaker system, press and hold the “EQ” button while you  
press the or buttons.  
NoTe: To reset the EQ Presets to factory settings, press and hold the EQ  
button for a few seconds.  
2
Select a frequency slider to adjust.  
Press the or buttons on the clip-on remote until the desired slider  
is highlighted.  
How to Adjust the 7-Band Graphic eQ Using the onboard controls  
For even greater personalization of your music, you can dial in your sound  
with the onboard 7-band graphic EQ.  
3
4
Increase or decrease the level of the frequency slider.  
Press the + or “–” buttons on the clip-on remote.  
1
2
3
4
5
enter the Graphic eQ Mode.  
Select the next frequency slider to adjust.  
Press and hold the “EQ” button while you press the or buttons.  
Press the or buttons on the clip-on remote until the next desired  
slider is highlighted.  
Select a frequency slider for adjustment.  
5
Increase or decrease the level of the frequency slider.  
Press the or buttons until the desired slider is highlighted.  
Press the “+” or “–” buttons on the clip-on remote.  
Increase or decrease the level of the frequency slider.  
6
7
Continue selecting and adjusting frequency sliders as desired.  
Rotate the knob.  
exit the Graphic eQ Mode.  
Select the next frequency slider for adjustment.  
Press the “EQ” button on either the clip-on remote or the speaker  
system. Or the unit will automatically exit this mode after several  
seconds.  
Press the or buttons until the next desired slider is highlighted.  
Increase or decrease the level of the frequency slider.  
Rotate the knob.  
NoTe: To reset the Graphic EQ to factory settings, press and hold the “EQ”  
button for a few seconds.  
6
7
Continue selecting and adjusting frequency sliders as desired.  
exit the Graphic eQ Mode.  
Press the “EQ” button again. Or the unit will automatically exit this  
mode after several seconds.  
NoTe: To reset the Graphic EQ to factory settings, press and hold the “EQ”  
button for a few seconds.  
14  
 
Charging Your iPhone or iPod  
Whenever your iPhone or iPod is docked and your Altec Lansing inMotion  
Max speaker system is plugged into an AC outlet, your iPhone or iPod is  
charging (until fully charged) – even if the speaker system is switched off.  
How to Store Preset Stations  
Your Altec Lansing Mix speaker systems clip-on remote enables you to  
program up to 4 FM station presets:  
1
2
3
Tune to the station you wish to store.  
Listening to the FM Radio  
While in “FM” mode, use the or buttons on your speaker system  
or clip-on remote to tune to the desired station.  
1
2
extend the FM antenna fully for  
Store the station.  
best FM reception.  
Press and hold the P1, P2, P3 or P4 button on the clip-on remote for  
a few seconds. You can store one FM station in each preset.  
Select “FM” mode.  
Press the “SOURCE” button on your  
speaker system or clip-on remote until  
“FM” appears on the LCD.  
To store other stations, repeat the above steps.  
How to recall Preset Stations  
3
4
Tune to the station you want to  
listen to.  
1
2
3
Make sure you are in “FM” mode.  
FM  
If you’re not in “FM” mode, press the “SOURCE” button on your  
speaker system or clip-on remote until “FM” appears on the LCD.  
Use the or buttons on your  
speaker system or enhanced remote to  
tune in the desired station. Press and  
Press a PReSeT button (P1, P2, P3 or P4) on the clip-on  
remote.  
hold these same buttons to find the next clear FM station.  
The radio will tune to your preset station.  
Adjust the volume.  
Use the knob on your speaker system to adjust the system  
volume. Or, use the “+” and “–” buttons on the clip-on remote.  
Adjust the volume.  
Use the knob on your speaker system to adjust the system  
volume. Or, use the “+” and “–” buttons on the clip-on remote.  
15  
 
Listening to Additional iPhone, iPod, non-Docking iPod or Other Audio Devices  
If you or a friend has an iPhone, iPod, non-iPod MP3 player or other  
non-docking audio device, you can enjoy it through your Altec Lansing  
Mix speaker system as well. Just connect it via the AUX 1 or AUX 2 jack.  
Heres how:  
1
2
Locate one of the two 3.5 mm  
stereo cables ( included).  
Plug one end of the stereo cable  
into your device.  
Your device should have either a  
headphone or LINE OUT jack for you  
to plug into.  
3
4
Plug the other end of the stereo  
cable into your speaker system’s  
AUX 1 or AUX 2 jack.  
The AUX jacks are located on the top of the speaker system next to  
the handle.  
Select “AUX 1” or “AUX 2” mode.  
Press the “SOURCE” button on your speaker system or the clip-on  
remote until “Auxiliary Input 1” or “Auxiliary Input 2” appears on the  
speaker systems LCD.  
5
6
Turn on your device and start playing it.  
Adjust the volume.  
Use the knob on the speaker system to adjust the volume. Or, use  
the “+” and “–” buttons on the clip-on remote.  
NoTe You may need to adjust the device volume also. Your devices  
volume should be set to approximately ¾ volume.  
16  
 
Personalizing the Power-On Message  
Whenever you turn on your Altec Lansing Mix speaker system, the Altec  
Lansing logo will appear for approximately 3 seconds followed by a  
personalized message, if you’ve set one. The Mix comes with no preset  
power-on message. To create a personalized message, just follow these  
instructions:  
2
3
Clear the message.  
Press the “SOURCE” button to clear the message.  
exit the Message Screen edit Mode.  
Press the knob to exit the Message Screen Edit Mode.  
1
enter the Message Screen edit Mode.  
Press and hold the “SOURCE,” “EQ,” and buttons. All four  
buttons must be pressed at approximately the same time while the  
Altec Lansing logo is displayed. The following message will appear on  
the LCD: “Add a personal message by selecting letters with the track  
buttons and rotary control.”  
Maintaining Your Speaker System  
Place your speaker system on a level surface away from sources of direct  
sunlight or excessive heat.  
Protect your furniture with a cloth or other protective material when placing  
your speaker system on a natural wood or lacquered finish.  
2
3
Add your personal message.  
Rotate the knob until the desired letter, number or symbol is  
displayed. Press the button to make your selection and move to  
the next space. Continue this process until your entire message is  
displayed.  
Clean your speaker system with a soft cloth moistened only with mild soap  
and water. Stronger cleaning agents, such as benzene, thinner or similar  
materials, can damage the surface of the unit.  
exit the Message Screen edit Mode.  
Press the knob to save the message and exit the Message Screen  
Edit Mode.  
How to Delete a Personalized Message  
1
enter the Message Screen edit Mode.  
Press and hold the “SOURCE,” “EQ,” and buttons. All four  
buttons must be pressed at approximately the same time while the  
Altec Lansing logo is displayed. The following message will appear on  
the LCD: “Add a personal message by selecting letters with the track  
buttons and rotary control.”  
17  
 
Troubleshooting  
Symptom  
Possible Problem  
Solution  
AC adapter isn’t plugged into a wall outlet  
or the connector isn’t plugged into the  
power supply jack on the back of the  
speaker system  
Plug the AC adapter into a wall outlet and plug the connector into the power  
supply jack on the back of the speaker system.  
Speaker system doesn’t  
respond (no power)  
Wall outlet is not functioning  
The batteries are dead.  
Plug another device into the same outlet to confirm the outlet is working.  
Replace with new batteries. (See the Getting Started section for details.)  
The power isn’t turned on.  
Turn on the speaker system by pressing the button. The LCD display turns  
on.  
Using the wrong adapter for iPhone or  
iPod or no adapter  
Make sure the adapter is the proper fit for your iPhone or iPod.  
iPhone or iPod doesn’t dock  
properly  
iPhone or iPod didn’t install properly  
Remove your iPhone or iPod from the dock and check for obstruction on the  
connectors in the dock and on your iPhone or iPod. Then reseat it in the dock  
and slide the guard down to protect it.  
18  
 
Troubleshooting  
Symptom  
Possible Problem  
Solution  
iPhone or iPod is not installed properly  
Remove your iPhone or iPod from the dock and check for obstructions on  
the connectors in the dock and on your iPhone or iPod. Then reseat it in the  
dock and slide the guard down to protect it.  
Your iPhone or iPod software is too old  
iPhone or iPod is locked up  
Upgrade software on your iPhone or iPod. For details visit  
iPhone or iPod doesn’t  
respond to the speaker  
system  
Please make sure your iPhone or iPod is working properly before docking into  
the unit. Please refer to your iPhone or iPod manual for details.  
Using 1st- or 2nd-generation iPod, iPod  
shuffle or other devices  
Your speaker system cannot control those iPods or other devices.  
iPhone or iPod is not installed properly  
Remove your iPhone or iPod from the dock and check for obstructions on the  
connectors in the dock and on your iPhone or iPod. Then reseat it in the dock  
and slide the guard down to protect it.  
iPhone or iPod is locked up  
Please make sure your iPhone or iPod is working properly before docking into  
the unit. Please refer to your iPhone or iPod manual for details.  
iPhone or iPod didn’t charge  
AC adapter isn’t plugged into a wall outlet, Plug the AC adapter into a wall outlet and plug the connector into the supply  
or the connector is not plugged into the  
power supply jack on the back of the  
speaker system  
jack on the speaker system. The iPhone or iPod will not charge when the  
speaker system is operating on batteries.  
19  
 
Troubleshooting  
Symptom  
Possible Problem  
Solution  
EQ settings are set too high.  
Sound source is distorted  
Decrease the EQ settings.  
If the iPhone or iPod original sound source (MP3) is of poor quality, distortion  
and noise are easily noticed with high-power speakers. Try a different audio  
source such as a music CD.  
Sound is distorted  
Battery is weak  
Replace current battery with a new battery.  
Clip-on remote is not pointed toward to  
the speaker system.  
Point the clip-on remote toward the Altec Lansing speaker system and move  
within 10 feet of the unit.  
Clip-on remote doesn’t work  
Sound source is connected to the AUX 1  
or AUX 2 jack.  
Clip-on remote will not control devices connected to the AUX 1 or AUX 2  
jack.  
No sound from the AUX 1  
or AUX 2 device, such as an  
iPhone, iPod, MP3 player or  
CD player connected to the  
AUX 1 or AUX 2 jack.  
Volume on the device is set too low  
Increase the volume on the device to approximately ¾ full volume.  
Set source selector to AUX 1 or AUX 2.  
Source selector is not set to AUX 1 or  
AUX 2.  
The speaker system  
exhibits erratic or  
unexpected behavior.  
Controls do not function.  
Static electricity, momentary interruption of 1. Disconnect the AC adapter cable plug from the speaker systems jack.  
power or abnormal operating conditions  
may be responsible.  
2. Wait 20–30 seconds.  
3. Reconnect the AC adapter cable plug to the speaker systems jack.  
4. Turn the unit back on  
There is radio interference.  
The unit is too close to a radio tower.  
Move the unit to see if the interference goes away.  
20  
 
Warranty  
ALTec LANSiNG oNe-YeAr LiMiTeD wArrANTY  
what Does the warranty cover?  
How will State Law Affect Your rights?  
This warranty gives you specific legal rights, and you may also have other rights which  
vary from state to state. Please note that in the European Union, you as a consumer  
might have other legal rights under national legislation of European Union Member  
States governing the sale of Altec Lansings goods. Those rights are not affected by this  
guarantee.  
Altec Lansing warrants that its products shall be free from defects in materials or  
workmanship, with the exceptions stated below.  
what is the Period of coverage?  
This warranty runs for one year from the date of purchase. The term of any warranties  
implied by law shall expire when your limited warranty expires. Some states and/or  
Member States in the European Union do not allow limitations on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
The above limited warranties and remedies are sole warranties and remedies available to  
purchaser, if, and to the extent, valid and enforceable under the applicable law.  
DiSPoSAL oF oLD eLecTricAL AND eLecTroNic eQUiPMeNT  
what Does the warranty Not cover?  
This symbol on the product or on its packaging indicates that this product  
shall not be treated as household waste. Instead it shall be handed over to  
the applicable collection point for the recycling of electrical and electronic  
equipment. By ensuring this product is disposed of correctly, you will help  
prevent potential negative consequences for the environment and human  
health, which could otherwise be caused by inappropriate waste handling of this  
product. The recycling of materials will help to conserve natural resources. For more  
detailed information about recycling of this product, please contact your local city office  
or your household waste disposal service.  
This warranty does not cover any defect, malfunction or failure that occurs as a result  
of: improper installation; misuse or failure to follow the product directions; abuse; or use  
with improper, unintended or faulty equipment. (For information on proper installation,  
operation and use consult the manual supplied with the product. If you require a  
consequential and incidental damages are not recoverable under this warranty. Some  
states do not allow the exclusion or limitation of incidental or consequential damages,  
so the above limitation or exclusion may not apply to you.  
what will Altec Lansing Do to correct the Problem?  
Altec Lansing will, at its option, repair or replace any product that proves to be defective  
in material or workmanship. If your product is no longer being manufactured, or is out of  
stock, at its option, Altec Lansing may replace your product with a similar or better Altec  
Lansing product.  
How to Get warranty Service  
To get a covered product repaired or replaced, you must contact Altec Lansing during  
the warranty period by email ([email protected]). You must include in your  
email, your name, address, email address, telephone number, date of purchase and  
a complete description of the problem you are experiencing. In the United States, you  
may alternatively contact Altec Lansing by telephone at 1-800-ALTEC88 – please be  
prepared to provide the same information. If the problem appears to be related to a  
defect in material or workmanship, Altec Lansing will provide you a return authorization  
and instructions for return shipment. Return shipments shall be at the customers  
expense, and the return must be accompanied by the original proof of purchase. You  
should insure the shipment as appropriate because you are responsible for the product  
until it arrives at Altec Lansing.  
21  
 
HeADQUArTerS 535 Rte. 6 & 209, Milford, PA 18337-0277 • 800-ALTEC-88. 570-296-4434. • Fax 570-296-6887  
eUroPe Scorpius 140, 2132 LR Hoofddorp, The Netherlands  
ASiA/PAciFic 23/F, Office Tower, Shun Hing Square Diwang Commercial Centre, 5002 Shen Nan Dong Road, Shenzhen, China 518008  
“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards.  
“Works with iPhone” means that an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to meet Apple performance standards.  
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.  
Patents pending.  
© 2009 Plantronics, Inc. All rights reserved.  
ALTEC, ALTEC LANSING, the Altec Lansing logo, the horn design, Mix, and iMT800 are trademarks or registered trademarks of Altec Lansing, a division of Plantronics, Inc.  
Plantronics, the logo design and Sound Innovation are trademarks or registered trademarks of Plantronics, Inc.  
iPod is a trademark of Apple, Inc., registered in the U.S. and other countries.  
iPhone is a trademark of Apple Inc.  
All other trademarks appearing herein are the property of their respective owners.  
Designed by Altec Lansing in the USA. Made in China.  
A13238 R04  
 

Aiphone Intercom System TB 6H User Manual
Alesis CD Player MMT 8 User Manual
Alpine CD Player 68 04123Z09 A User Manual
Amana Dishwasher W10261420A User Manual
AMX Network Card NXP TPI 4 User Manual
Audiovox Car Stereo System ACD28 User Manual
Axis Communications Security Camera 207MW User Manual
Axis Communications Security Camera 31922 User Manual
BB Electronics Home Theater Server Vlinx VESR9xx User Manual
Beckett Water Gardening Water Dispenser PF357 User Manual