American DJ Music Mixer XDM 221 User Manual

User Instructions  
XDM-221  
PREAMP MIXER  
Thank you for purchasing this American DJ® product. The XDM-221 is ready to be used,  
there is no assembly required. Please read the following instructions before installing  
or using your new unit. The XDM-221 has a 2 year limited warranty!  
CAUTION! - Keep this device away from rain and moisture!  
Safety Instructions  
Always plug in the power last. Make sure that the Power switch is set to the OFF position before connecting other devices  
to the mixer.  
Keep away from heaters and other heating sources!  
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch on the mixer  
immediately. The arising condensation of water might damage your device. Leave the device switched off until it has  
reached room temperature.  
Never put any liquids on the mixer or close to it. Should any liquid enter the device, disconnect from main power  
immediately. Have the device be checked by a qualified service technician before operating again. Any damage caused by  
liquid entering the device is not subject to warranty!  
Never let the AC cord come in contact with other cables! Handle the AC cord and all AC connections with particular care.  
Make sure that the available voltage is not higher than stated on the AC voltage selector (22).  
Before the device is switched on, all fader and volume controls should be set to 0 or minimum position.  
Damages caused by manual modifications to the device or unauthorized operation by unqualified persons are not  
subject to warranty.  
There are no user serviceable parts inside the mixer. For maintenance and/or service, contact an authorized  
American DJ® dealer.  
© American DJ® AUDIO Los Angeles, CA 90058 USA  
Specifications subject to change without notice. XDM-221 User Instructions page 1  
 
Functions  
12  
2
3
2
1
15  
6
13  
14  
4
7
8
10  
9
11  
5
(1) POWER SWITCH  
(2) LINE/PHONO SWITCH - Used to select the input (LINE or PHONO) to be sent to channel 1 or 2. Can also be used for  
TRANSFORMER SCRATCHING.  
(3) BASS/TREBLE CONTROL - Used to increase or decrease the LOW’s and HIs of the input signal.  
(4) CHANNEL FADER CHANNEL 1 / CHANNEL 2 - Used to adjust the input level of each channel.  
(5) CROSSFADER - Mixes the signals of channel 1 and channel 2. When the crossfader is set in the center position, both  
channels can be heard at once.  
(6) BASS/TREBLE CONTROL - Used to increase or decrease the LOWs and HIs of the input signal.  
(7) CUE LEVEL CONTROL - Adjusts the headphone output level.  
(8) CUE MIXING CONTROL - Selects the channel for monitoring. The monitor signal comes from the Prefader. This means  
it will not be affected by the channel faders, so that you can monitor an input signal without the sound coming from the  
AMP output. Connect your headphones to the PHONES JACK (10). Turn the CUE MIXING CONTROL (8) to CUE and  
select CH1 or CH2 with the CUE SWITCHES (9). When you turn the CUE MIXING CONTROL to PGM (CUE SWITCHES  
without function), you can cue the output signal of the mixer. If the CUE MIXING CONTROL is set to the center position,  
you can cue both the channel signal you have selected and the output signal. With the CUE LEVEL CONTROL (7), you  
can adjust the phones volume without changing the output signal.  
(9) CUE SWITCH CHANNEL 1 / CHANNEL 2 - Use the cue switch in order to select the channel to be monitored.  
© American DJ® AUDIO Los Angeles, CA 90058 USA  
Specifications subject to change without notice. XDM-221 User Instructions page 3  
 
Functions (Cont.)  
(10) PHONES JACK - Connect headphones to this jack. Headphones from 8 Ohms to 600 Ohms can be used. 16 Ohms  
is recommended.  
(11) BEAT INDICATOR CHANNEL 1 / CHANNEL 2 - Use the cue switch in order to select the channel to be monitored.  
(12) TALKOVER BUTTON - Press the talkover button when you want to use the microphone. When the button is pressed,  
all signals except the microphone level are decreased by 15dB. In the OFF position, all signals return to their original level.  
When talkover is ON, the red L.E.D. is lit.  
(13) DJ MIC CONTROL - Adjusts the microphone volume.  
(14) BASS/TREBLE CONTROL FOR DJ MIC - Use bass and treble adjustment knobs to fine tune the DJ MIC signal.  
Increase LOWs by turning the BASS CONTROL to the right. Increase HIs by turning the TREBLE CONTROL to the right.  
Inputs and Outputs  
23  
GND  
AC IN  
20  
ACVOLTAGE  
SELECTOR  
115 / 230V  
115  
L -  
FUSE  
R -  
AMP  
REC  
LINE 2  
PHONO 2  
LINE 1  
PHONO 1  
OUTPUT  
CH 2  
CH 1  
22  
21  
19  
18 17  
16  
(16), (17) LINE / PHONO INPUT JACK - Input jacks for CH1, CH2, and CH3. Connect turntables equipped with MM  
pickup cartridges to the PHONO input. CD Players or Tape Decks should be connected to the LINE input. Line level  
musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to the LINE  
inputs.  
(18) REC OUT - To record your record unit. The REC OUT level is not influenced by the master control.  
(19) AMP OUTPUT - Parallel output for P.A. output. Connect with the input of power amplifier.  
(20) GND (Ground Terminal) - Connect this terminal to ground lead of the turntable. This helps to reduce humming and  
popping noises.  
(21) FUSE - Fuseholder. Only replace the fuse when the device is disconnected from power supply. Only replace fuses  
with the same power and rating.  
(22) AC VOLTAGE SELECTOR - Make sure that the selector is properly set desired voltage (115V or 230V).  
(23) MIC INPUT - 1/4 inch (6.3 mm) jack plug for microphone input to mixer.  
© American DJ® AUDIO Los Angeles, CA 90058 USA  
Specifications subject to change without notice. XDM-221 User Instructions page 4  
 
Replacing the Crossfader  
Instructions for replacing the crossfader:  
• Disconnect from main power supply  
• Remove the fader knob.  
• Remove the two outer screws.  
Take the fader out and unplug the connection cable.  
• Connect the new fader and replace back into mixer.  
Technical Specifications - model XDM-221  
Inputs:  
Microphone  
Phono  
Line  
1.5mV, 600 Ohm  
1.2mV, 47kOhm  
100mV, 27kOhm  
28V, peak to peak  
20Hz-20KHz, ± 1dB  
<0,03%  
Output  
Frequency range  
Distortion  
S/N-ratio  
Talkover  
>75dB  
-15dB  
Tone control  
Treble: 10Khz ± 12dB  
Bass: 100 Hz ± 12dB  
16 Ohms  
Headphone impedance  
Power supply  
AC115/230V,50/60Hz  
Dimensions  
10” W x 7.5” D x 3.75” H  
256 x 192 x 100 mm  
5 lbs. / 2.3 kg  
Weight  
© American DJ® AUDIO Los Angeles, CA 90058 USA  
Specifications subject to change without notice. XDM-221 User Instructions page 5  
 

Aastra Telecom Telephone AASTRA 9116 User Manual
Alcatel Lucent Answering Machine Alcatel 4400 User Manual
Alliance Laundry Systems Washer FTS90AN User Manual
Alpine Car Stereo System 7909 User Manual
Alto Shaam Food Warmer HFM 30 User Manual
Amana Range W10181330A User Manual
ATMT MP3 Player MP130 User Manual
Audiovox Automobile Alarm IMO 720 User Manual
Behringer Musical Instrument Amplifier LX110 User Manual
Eureka Tents Tent High Camp User Manual