American Standard Plumbing Product 206490X User Manual

Installation  
Instructions  
2064.90X  
SERIN  
DECK MOUNT BATH FILLER  
Thank you for selecting American-Standard...  
the benchmark of fine quality for over 100 years.  
To ensure that your installation proceeds smoothly--  
please read these instructions carefully before you begin.  
Certified to comply with ANSI A112.18.1M  
M968830 Rev.1.4  
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.  
Recommended Tools  
ROUGHING-IN DIMENSIONS  
6-1/2" to 12"  
(165mm to 305mm)  
2" D.  
(52mm) D.  
3-1/4" D.  
(82mm) D.  
9-1/2"  
9-3/4"  
Flat Blade Screwdriver  
(240mm)  
(247mm)  
2-3/4"  
(71mm)  
Tubing Cutter  
6-3/4"  
(170mm)  
2-1/16" D.  
(52mm) D.  
MOUNTING  
SURFACE  
1-1/8 D.  
Adjustable Wrench  
Channel Locks  
3'  
(76mm)  
*Wrench  
1-1/2 MAX.  
(38mm) MAX.  
1-3/16" MAX.  
(30mm) MAX.  
1-3/16 D.  
(30mm) D.  
(C)  
12 MAX.  
(H)  
3/4-14 MALE  
N.P.T. INLETS  
1-1/16 D.  
(27mm) D.  
(305mm)  
*Hex key  
*Supplied with Fitting  
Turn off hot and cold water  
supplies before beginning.  
PREPARE TUBE AND TEE ASSEMBLY  
CAUTION  
SPOUT ASSEMBLY  
1
2
Install RUBBER RING (1) into ESCUTCHEON RING (2) and  
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center  
VALVE (2) location (between 6-1/2" and 12"). If necessary,  
cut and/or bend TUBING carefully. Make sure tube bend is  
close to the TEE (1) so that it will not effect the compression  
joint at the VALVE CONNECTION.  
place over mounting hole.  
Insert SPOUT SHANK (3) through center hole of MOUNTING LEDGE.  
Make sure that the RUBBER RING (1) is properly seated in RECESS  
of ESCUTCHEON RING (2).  
Assemble RUBBER WASHER (4) and BRASS WASHER (5) onto  
SHANK (3). From underside of ledge secure SPOUT (7) into position  
with LOCKNUT (6).  
Remove COUPLING NUT (3) and FERRULE (4) from each  
VALVE (2) and slide onto TUBING (5).  
4
3
1
5
3
4
6-1/2" to 12"  
(165mm to 305mm)  
7
RECESS  
2
3
MOUNTING  
SURFACE  
1
MOUNTING  
SURFACE  
4
6
2
NOTE  
VALVE inlet is  
3/4-inch NPT male.  
5
 
HANDSHOWER INSTALLATION (For 2064.901 only)  
6
7
11  
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT  
center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2)  
is properly seated in SPRAY ESCUTCHEON (1). Install RUBBER WASHER (3), BRASS WASHER (4)  
and LOCKNUT (5) from underside of ledge.  
9
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT (5).  
Install SEAL (9) and connect HOSE (10) to outlet nipple at the bottom of TEE (7). Tighten firmly.  
6
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY  
HOLDER (6) and SPRAY ESCUTCHEON (1). Note: SPRAY  
HOLDER (6) must be seperate from ESCUTCHEON (1) to  
pass HOSE (8) through ESCUTCHEON.(1)  
1
3
2
4
5
Insert SEAL (9) into SHOWER HOSE (8). Connect HOSE (8)  
to HOSE (10).  
9
7
9
10  
Install SEAL (9) and connect HAND SHOWER (11) to  
SPRAY HOSE (8).  
8
When not in use, HANDSHOWER should be seated  
in the HOLDER.  
NOTE  
MAKE WATER SUPPLY CONNECTIONS  
HAND  
SHOWER  
Connect HOT water supply to LEFT INLET  
UNION (1) and COLD water supply to  
RIGHT INLET UNION (2). Pipe connections  
are 3/4" NPT. Use sealant or Teflon tape  
on pipe connections.  
TRANSFER KNOB  
Do not solder directly to valve body.  
TEST INSTALLED FAUCET  
7A  
COLD  
With HANDLES in OFF position, turn on  
WATER SUPPLIES and check all connections  
for leaks.  
2
3/4" NPT  
HOT  
Operate both HANDLES to flush water lines  
thoroughly.  
1
Lift HAND SHOWER from HOLDER, direct spray  
into tub. Lift TRANSFER KNOB to check HAND  
SHOWER and HOSES for leaks.  
3/4" X 3/4" NPT UNION  
(NOT SUPPLIED)  
IMPORTANT: It is strongly recommended that access be  
provided for all enclosed mechanical parts to this system.  
3/4" NPT  
Turn handles "off" and replace HAND SHOWER.  
Before the bathroom is completely finished, you may  
want to remove spout, handshower, and handles to  
avoid damage during construction.  
2
8
To remove handles, reverse steps in section 4.  
To remove SPOUT (1), proceed as follows:  
Unthread LIFT ROD KNOB (2) and remove.  
VIEW "A"  
3
4
1
6
Remove PLUG BUTTON (3) and remove SET SCREW (4) using  
4mm hex wrench supplied.  
Lift SPOUT (1) off SHANK (5) carefully and remove RUBBER  
RING (6).  
Unthread SHANK SLEEVE (7) and remove from SHANK (5).  
VIEW "A"  
8
7
Hex wench  
(supplied)  
Reverse sequence to re-install SPOUT (1). Be sure RUBBER  
RING (6) is properly seated in its recess at the base of the  
SPOUT (1). Make certain SET SCREW (4) is properly aligned  
and tight so that SPOUT (1) is locked in place.  
5
CARE INSTRUCTIONS:  
9
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.  
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A  
CLOTH WITH A COARSE SURFACE.  
M968830 Rev.1.4  
 
SERIN  
DECK-MOUNT  
BATH FILLER  
MODEL NUMBER  
M962418-YYY0A  
SPOUT KIT (2064.901)  
2064.90X  
M962489-YYY0A  
SPOUT KIT (2064.900)  
M962269-YYY0A  
SPOUT END  
M962347-YYY0A  
SPOUT ESCUTCHEON KIT  
Replace the "YYY" with  
appropriate finish code  
CHROME  
SATIN NICKEL  
002  
295  
M950245-YYY0A  
HANDLE  
M962346-YYY0A  
TRANSFER  
ASSEMBLY  
ROD ASSEMBLY  
M953169-YYY0A  
030274-0070A  
SHANK MOUNTING KIT  
HAND SHOWER  
030275-0070A  
SHANK SLEEVE KIT  
M962414-YYY0A  
DECK  
ESCUTCHEON KIT  
918555-0070A  
HANDLE SCREW  
918049-0070A  
HANDLE ADAPTER  
012668-0070A  
SHANK KIT  
994053-0070A  
VALVE  
028664-YYY0A  
HAND SHOWER  
HOLDER  
M961634-0070A  
VALVE  
MOUNTING  
KIT  
028679-0070A  
TUBE & TEE  
ASSEMBLY  
028699-0070A  
COUPLING (FOR TRANSFER)  
028698-0070A  
COUPLING  
A952849-0070A  
012078-0070A  
VALVE COUPLING KIT  
CHECK VALVE  
028667-0020A  
HAND SHOWER HOSE  
HOT LINE FOR HELP  
For toll-free information and answers to your questions, call:  
1 (800) 442-1902  
051343-0070A  
HOSE KIT  
Weekdays 8:00 a.m. to 6:00 p.m. EST  
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)  
Weekdays 8:00 a.m. to 7:00 p.m. EST  
IN MEXICO 01-800-839-12-00  
Product names listed herein are trademarks of American Standard Inc.  
M968830 Rev.1.4  
©
AS America, Inc. 2008  
 

Acer Personal Computer M5150 User Manual
Adesso Scanner 3200 series User Manual
ADTRAN Network Card T1 FT1 + DSX 1 User Manual
ADT Security Services Power Supply ADT APS 6R User Manual
AG Neovo Flat Panel Television H 17 User Manual
Airlink101 Network Card AWLC6080 User Manual
Alps Electric Stereo System TDGB2 Series User Manual
Amana Refrigerator W10154917A User Manual
Bakers Pride Oven Fryer LGF User Manual
Beko Dishwasher DW603 User Manual