Audiovox Remote Starter 128 7828A User Manual

Model APS-620  
Owner’s Manual  
KEYLESS ENTRYOPERATION  
The Lock button on the transmitter is used to lock the vehicle's doors, the Unlock button  
is used to unlock the vehicle's doors. To lock or unlock the doors simply press and  
release the desired function button one time. As a keyless entry unit, when the doors are  
locked, for your convenience, the parking lights and or vehicle horn will flash/beep once.  
When the doors are unlocked the parking lights and or vehicle horn will flash/beep twice.  
REMOTE CAR FINDER  
The Lock or Unlock buttons are also used to access the car finder mode. This feature is  
particularly useful in a crowded parking lot where finding your car may be difficult. To  
access the car finder mode, while within range of your car, simply press and hold either  
the lock or unlock button of your transmitter for three seconds. The parking lights will  
begin to flash, and if connected, the vehicle horn will beep making your vehicle audible as well as more  
visible. The lights and or horn will stop automatically after 30 seconds. If you wish to turn off the car finder  
mode prior to the expiration of the 30 second timer, press and hold for three seconds either the lock or unlock  
buttons a second time, or press and release the Trunk/Start button one time.  
REMOTE TRUNK RELEASE  
If you have electric trunk release in your vehicle and the remote trunk release option was added, simply  
press and hold the Key/Trunk button of your keychain transmitter for 4 seconds or until the electric trunk of  
your vehicle opens. . .  
REMOTE STARTING THE VEHICLE  
This unit will not start the vehicle if any one of the following situations exists:  
The vehicle's hood lid is opened. The gear shift selector is not in Park.  
The brake pedal is depressed. The system is placed in the override position.  
1) To start the vehicle, press and release the Key/Trunk button two times within 2 seconds. The vehicle will  
start and remain running for the pre-programmed 5,10,15,20 minute run cycle. As a visual indication, the  
parking lights will flash or remain on depending on the setting by your installation center.  
2) When you arrive at the vehicle, turn the ignition key to the ON position (not the spring loaded start position),  
then step on the brake pedal to disengage the remote starter. The vehicle will continue to run, but now on  
it's own power.  
NOTE: The engine will stop running before the pre-programmed run cycle has expired if you perform any  
one of the following functions;  
Press and release Key/Trunk button on the keychain transmitter two times within 2 seconds.-Depress  
the brake pedal. - Open the vehicle's hood -Place the unit in the safety control disabled mode.  
THE OPTION BUTTON of your transmitter may or may not be used with your system but may be used with  
a second similar Audiovox Model system that may be installed on a second vehicle in your family.  
PUSH-BUTTON SAFETY CONTROL/PROGRAM SWITCH  
The Push-Button safety control switch allows you to temporarily disable the remote starting function of the  
system. This is recommended whenever the vehicle is being serviced. To place the system in the service/  
temporary disabled mode:  
1) With the system disarmed/unlocked, and the ignition switch off Press and Hold the Push-Button Switch  
on.  
2) Turn the ignition switch on, off, on, off, on, off.  
3) The LED begins to flash two short flashes followed by one long flashes and continues this pattern until  
returned to normal mode of operation.  
This puts the unit into the R/S Override mode indicating that the remote start system is in the service/  
temporary disabled mode and will not start from RF or any other input Telematic input or otherwise.  
To Exit R/S Override Mode  
1) With the system disarmed, Press and Hold the Push-Button Switch on.  
2) Turn the ignition switch on, off, on, off, on, off.  
3) The LED turns off indicating that the R/S unit is fully functional once again.  
OPERATING ON AUTOMATIC START UP TIMER MODE  
Your system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period. This  
feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm  
is to periodically start the engine.  
128-7828A  
Rev A: Running change to transmitter engraving from APS620TX to 620TX 6/06  
1 of 4  
 
DELETING TRANSMITTERS FROM YOUR SYSTEM:  
It may be necessary to delete a lost transmitter or to reprioritize a transmitter that is programmed to your  
system. To remove a transmitter that has been programmed in your system:  
1) Enter the transmitter program mode of channel 1 as indicated above.  
2) Press and hold any transmitter button that has not been programmed into channel 1 until you hear a  
chirp, then release and immediately press the same button a second time until you hear a long chirp  
followed by a short chirp. This action erases the transmitter.  
If the transmitter you wish to erase has been lost or stolen then following the information below will  
successfully remove the transmitter.  
NOTE: For this procedure, you must have all transmitters you wish to remain programmed in your system  
available.  
1) Enter the transmitter program mode of channel 1 as indicated above.  
2) Press and hold the lock button of each transmitter you wish to operate the lock function of your unit  
making sure you occupy all 4 transmitter slots. In other words, you have three transmitters you wish to  
remain programmed. Press and hold the lock button of transmitter one until a long chirp is heard, then  
press and hold the lock button of transmitter two, then press and hold the lock button of transmitter three,  
followed by pressing and holding the lock button of transmitter one again. This action fills all 4 receiver  
slots.  
3) Advance to receiver channel 2 by pressing the push-button switch one time.  
4) Press and hold the unlock button of each transmitter you wish to operate the unlock function of your  
vehicle, again making sure all 4 transmitter slots are filled.  
4) Advance to receiver channel 3 by pressing the push-button switch one time.  
5) Press and hold the unlock button of each transmitter you wish to operate the start function of your  
vehicle, again making sure all 4 transmitter slots are filled.  
If you are uncomfortable about the programming of additional transmitters as outlined in the processes  
above please contact your installation center or call the technical service number listed on the back of the  
transmitter for help.  
BATTERY REPLACEMENT  
The transmitter incorporates a small LED visible through the case which is used to indicate battery condition.  
You will notice a decrease in transmitter range as the battery condition deteriorates. Transmitter battery  
replacement is recommended at least every 10 to 12 months, depending upon how frequently the transmitter  
is used.  
To replace the battery in the 620TX:  
1) Remove the small # 0 Phillips head screw from the rear of the case.  
2) Remove the rear cover to access the discharged battery paying attention to the proper polarity orientation.  
3) Carefully remove and properly dispose of the discharged battery.  
4) Insert the new battery, close the case, then reinstall the small case screw removed in step 1.  
5) If you accidently dislodge the circuit board from the transmitter housing, be certain that the rubber mem-  
brane is seated properly, and the buttons are properly exposed from the front view of the case, then insert  
the circuit board, and return to step #4.  
APS620TX Uses GP23 Battery  
CAUTION!!  
CARBON MONOXIDE GAS CAN CAUSE SERIOUS INJURYAND EVEN DEATH!  
It is the sole responsibility of the user to operate the vehicle this system is installed in a  
safe manner.  
This device must not be used in an enclosed space like a garage, attached or detached,  
car port, or any partially enclosed areas. Also this device must be placed in the service  
mode when dropping the vehicle off for service to prevent injury to the service  
technician.  
128-7828A  
3 of 4  
 
ORDER FORM FOR 620TX  
Attention: Transmitter Ordering Department  
Important: To help us expedite your order, please print all of the information legibly and mail  
this form and your payment according to the instructions below.  
Note: Transmitter model number found on back of case.  
1) Transmitter Model Number_____________________  
2) Name: _______________________________________  
3) Address: ______________________________________  
4) City: ________________ State: _____ Zip Code: ________  
Order 620TXP-300  
5) Telephone Number: (_____) _______________  
6) Total Number Of Transmitters Required:  
If Lock & Unlock Buttons  
Are Blue & 620TXP-304 If  
Lock Unlock Buttons Are Red  
Cost Per Transmitter is:  
$65.00  
Multiply By Number Of Transmitters  
X ______  
7) Enter Total Amount Enclosed _________________  
(New York State Residents must include the appropriate sales tax)  
8) Method of Payment:  
Mastercard Visa Check or Money Order (do not send cash)  
Make Checks Payable To Audiovox Corporation  
Credit Card Number: _________________________________  
Credit Card Expiration Date: ____ / _____ / _____  
Credit card purchasers can order additional or replacement  
transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and  
follow the instructions from the operator interface.  
9) Mail this form along with your payment to:  
Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y., 11788  
Attn.:TRANSMITTERDEPARTMENT  
Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, NY 11788  
128-7828A  
128-7828A  
4 of 4  
 

Acer Laptop TravelMate 4260 User Manual
Allied Telesis Network Card AT 2931SX User Manual
Allied Telesis Network Card AT WCC201 Series User Manual
Allied Telesis Switch AT GS950 48PS User Manual
Alto Shaam Oven 714ESG Over User Manual
Asus Computer Hardware 90MB0DU0M0AAY0 User Manual
A T International Cordless Telephone CL83101 User Manual
Axis Communications Tablet Accessory P8221 User Manual
Axor Plumbing Product 13898000 User Manual
Behringer Car Speaker B1220DSP User Manual