Avocent Cell Phone Accessories SM5 MV2503G3 User Manual

|
SM5-MV2503G3 Vehicle Specific Mounting Bracket with Slim-Grip™ Universal Mobile Phone Holder  
SM050-2 Slim-Grip™  
Universal Phone Holder  
SP-SBH-Kit  
Package Contents:  
Dual-T Head with  
Swivel Ball Socket &  
Locking Ring  
(1) MV-25-03-G3 - Pro.Fit Vehicle Specific Mounting Bracket*  
(1) SM050-HPB-2 - Slim-Grip™ Universal mobile phone holder  
(1) SP-SM050-LF - Extra Long Support Legs (2 Pack) for larger phones  
(1) SP-SBH-Kit - Dual-T Head with Swivel Ball Socket & Locking Ring  
88mm  
expandable to  
138mm  
with Extra  
Long Support  
Legs  
Compatible with:  
• Most non-flip style phones regardless of whether protective skin or  
sleeve (sold separately) is attached to the phone.  
SP-SM050-LF  
Extra Long  
Support Legs  
(2 Pack)  
Vehicle Specific  
*See included Pro.Fit maual for Vehicle Specific Mounting Bracket instructions. For  
questions regarding installation of the Vehicle Specific Mounting Bracket, contact Pro.Fit  
directly at 800.388.0073.  
Mounting Bracket  
(See included Pro-Fit  
manual for instructions)  
Patent Pending  
Slim-Grip™ Holder Instructions  
Install the Vehicle Specific Mounting Bracket  
Step 1. See the included Pro.Fit VSM Bracket manual for instructions  
on installing the VSM Bracket. Arkon reccomends that you  
have the VSM bracket professionally installed. Arkon is  
not responsible for any unintended damaged caused by  
installation of the VSM Bracket.  
Step 1. If necessary, adjust the support legs (D) by sliding them  
laterally. These provide support for your device (sold  
seperately) .  
Connect Dual-T Head to VSM Bracket  
D
Step 1.  
Slip the tightening ring (A) over the VSM bracket ball. Snap  
the dual-T head adapter plate (B) on to the bracket ball  
(C). Screw the tightening ring over the adapter plate until  
securely holding the plate. Adjust the angle as needed.  
D
B
C
Step 2. Support the holder in place with your hand. Place device on  
the lower support legs (E) and push down with moderate  
pressure to activate the spring-loaded grip mechanism.  
A
Step 3. Slide the top of the device under the top support legs (F)  
until it fits snuggly against the holder.  
Attach Holder to Dual-T Head  
F
Step 1.  
Connect the dual T-slots (A) on holder to the dual T-tabs (B)  
on the pedestal head.  
A
B
E
* If necessary, install the (2) extra long support legs  
(SP-SM050-LF) to accommodate large sized phones.  
Safety Precautions  
!
Do not install Arkon products over an air bag cover or within the air  
bag deployment zone. Arkon Resources, Inc. assumes no responsi-  
bility of liability for injury or death as a result of car crashes and/or  
air bag deployment.  
The Mobile Mounting Specialists™  
Consumer Hotline:  
Arcadia, CA 91006 USA  
USA (800) 841-0884  
INT’L (626) 254-9005  
Monday - Friday 9am-5pm, PST  
Designed in USA | Made in the USA & China  
© Copyright 2010 Arkon Resources, Inc.  
Arkon is not responsible for any damages caused to your car, your  
device, or yourself due to the installation or use of this pedestal mount.  
 

ADTRAN Network Card OPTI 6100 User Manual
Advantech Computer Monitor PPC A84 User Manual
AEG Oven B3040 1 User Manual
Agilent Technologies Computer Accessories N5700 User Manual
Aiphone Weather Radio A User Manual
Alpine Car Stereo System CDE 110 User Manual
Alpine Speaker SWR 1021D User Manual
Athena Technologies Speaker AS 1C6 User Manual
Aztech Systems Router 305E User Manual
BB Electronics Network Router Digi One IA User Manual