Axis Communications Car Video System P7216 User Manual

INSTALLATION GUIDE  
AXIS P7216 Video Encoder  
 
Europe  
Tel: +46 46 272 18 00  
Fax: +46 46 13 61 30  
This digital equipment fulfills the requirements for RF  
emission according to the Class B limit of EN 55022.  
This product fulfills the requirements for immunity  
according to EN 61000-6-1 residential, commercial and  
light-industrial environments.  
This product fulfills the requirements for immunity  
according to EN 61000-6-2 industrial environments.  
Australia/New Zealand  
This digital equipment fulfills the requirements for RF  
emission according to the Class B limit of AS/NZS CISPR 22.  
Japan  
この装置は、クラスB 情  
報技術装置です。この装  
置は、家庭環境で使用することを目 的としていま  
すが、この装置がラジオやテレビジョン受信機に  
近接  
して使用されると、 受信障害を引き起こすこ  
とがあります。 取扱説明書に従って正しい取り扱  
いをして下さい。  
Korea  
이 기기는 가정용(B급) 전자파적합기기로서 주로  
가정에서 사용하는 것을 목적으로 하며, 모든 지  
역에서 사용할 수 있습니다.  
Safety  
This product complies with IEC/EN/UL 60950-1, Safety of  
Information Technology Equipment.  
The power supply used with this product shall fulfill  
the requirements for Safety Extra Low Voltage  
(SELV) and Limited Power Source (LPS) according to  
IEC/EN/UL 60950-1.  
Disposal and Recycling  
When this product has reached the end of its useful life,  
dispose of it according to local raws and regulations. For  
information about your nearest designated collection point,  
contact your local authority responsible for waste disposal.  
In accordance with local legislation, penalties may be  
applicable for incorrect disposal of this waste.  
Europe  
This symbol means that the product shall not be  
disposed of together with household or commercial waste.  
Directive 2012/19/EU on waste electrical and electronic  
equipment (WEEE) is applicable in the European Union  
member states. To prevent potential harm to human health  
and the environment, the product must be disposed of in  
an approved and environmentally safe recycling process.  
For information about your nearest designated collection  
point, contact your local authority responsible for waste  
disposal. Businesses should contact the product supplier for  
information about how to dispose of this product correctly.  
This product complies with the requirements of  
Directive 2011/65/EU on the restriction of the use of  
certain hazardous substances in electrical and electronic  
equipment (RoHS).  
China  
This product complies with the requirements of the  
legislative act Administration on the Control of Pollution  
Caused by Electronic Information Products (ACPEIP).  
Contact Information  
Axis Communications AB  
Emdalavägen 14  
223 69 Lund  
Sweden  
 
     
 
AXIS P7216 Video Encoder  
Safety Information  
Read through this Installation Guide carefully before installing the product. Keep the Installation  
Guide for future reference.  
Hazard Levels  
DANGER  
WARNING  
CAUTION  
NOTICE  
Indicates a hazardous situation which, if not avoided, will result in  
death or serious injury.  
Indicates a hazardous situation which, if not avoided, could result  
in death or serious injury.  
Indicates a hazardous situation which, if not avoided, could result  
in minor or moderate injury.  
Indicates a situation which, if not avoided, could result in damage  
to property.  
Other Message Levels  
Important  
Indicates significant information which is essential for the product  
to function correctly.  
Note  
Indicates useful information which helps in getting the most out  
of the product.  
 
5
AXIS P7216 Video Encoder  
Safety Instructions  
NOTICE  
• The Axis product shall be used in compliance with local laws and regulations.  
• To use the Axis product outdoors, or in similar environments, it shall be installed in an  
approved outdoor housing.  
• Store the Axis product in a dry and ventilated environment.  
• Avoid exposing the Axis product to vibration, shocks or heavy pressure.  
• Do not install the product on unstable or vibrating brackets, surfaces or walls.  
• Use only applicable tools when installing the Axis product. Excessive force could cause  
damage to the product.  
• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.  
• Use only accessories that comply with technical specification of the product. These can be  
provided by Axis or a third party.  
• Use only spare parts provided by or recommended by Axis.  
• Do not attempt to repair the product by yourself. Contact Axis support or your Axis  
reseller for service matters  
Transportation  
NOTICE  
• When transporting the Axis product, use the original packaging or equivalent to prevent  
damage to the product.  
Battery  
The Axis product uses a 3.0 V CR2032 lithium battery as the power supply for its internal real-time  
clock (RTC). Under normal conditions this battery will last for a minimum of five years.  
Low battery power affects the operation of the RTC, causing it to reset at every power-up. A log  
message will appear when the battery needs replacing.  
The battery should not be replaced unless required, but if the battery does need replacing, contact  
Axis support at www.axis.com/techsup/ for assistance.  
WARNING  
• Risk of explosion if the battery is incorrectly replaced.  
• Replace only with an identical battery or a battery which is recommended by Axis.  
• Dispose of used batteries according to local regulations or the battery manufacturer's  
instructions.  
 
6
AXIS P7216 Video Encoder  
Installation Guide  
This Installation Guide provides instructions for installing AXIS P7216 Video Encoder on your  
network. For other aspects of using the product, see the User Manual available at www.axis.com  
Installation Steps  
1. Make sure the package contents, tools and other materials necessary for the installation  
are in order. See page 7 .  
2. Study the hardware overview. See page 7 .  
3. Study the specifications. See page 10.  
4. Install the hardware. See page 13.  
5. Access the product. See page 14.  
Package Contents  
Axis P7216 Video Encoder  
Power adapter model  
-
Type PS-P  
Mounting kit  
-
-
4 surface pads  
2 brackets  
Terminal connectors  
-
-
4 I/O 6–pin connector  
4 RS-485/422 2x2–pin connector  
Installation and Management Software CD  
Printed materials  
-
Installation Guide (this document)  
Hardware Overview  
1
Power connector  
 
7
   
AXIS P7216 Video Encoder  
2
3
4
5
6
7
8
9
Network connector SFP  
Network connector RJ45  
Auxiliary connector RJ45 (maintenance)  
Card slot (microSD) x4  
I/O terminal connector x4  
RS-485/422 connector x4  
Control button x4  
Protective earth  
1
2
3
4
5
6
7
8
9
Video input connector BNC x16  
Network LED RJ45  
Network LED SFP  
Network LED auxiliary  
Power LED  
Status LED 1–4  
Audio out connector  
Audio in connector 2  
Audio in connector 1  
LED Indicators  
LED  
Color  
Green  
Amber  
Indication  
Net-  
work  
Steady for connection to a 1 GBit/s network. Flashes for network activity.  
Steady for connection to a 10/100 MBit/s network. Flashes for network  
activity.  
Unlit  
No network connection.  
Status  
Power  
Green  
Amber  
Red  
Steady green for normal operation.  
Steady during startup and when restoring settings.  
Slow flash for failed upgrade.  
Green  
Amber  
Normal operation.  
Flashes green/amber during firmware upgrade.  
 
8
 
AXIS P7216 Video Encoder  
Connectors  
For specifications, see page 10.  
BNC connector - Each video input is terminated using a coax/BNC connector. Connect a 75 Ohm  
coaxial video cable; the recommended maximum length is 800 feet (250 meters).  
Note  
75 Ohm video termination can be enabled/disabled for the video input via the product's  
web page at Video & Audio > Video Input > Video termination. This termination is enabled  
on factory default. In cases where the product is to be connected in parallel with other  
equipment, for optimum video quality, it is recommended that termination be enabled for  
only the last device in the video signal chain.  
Network connector - RJ45 Ethernet connector.  
SFP connector - The unit can only use one Network interface, either an SFP module or RJ45  
connector. SFP module has higher priority than the RJ45 connector.  
NOTICE  
The product shall be connected using a shielded network cable (STP). All cables connecting  
the product to the network switch shall be shielded (STP) and intended for their specific  
use. Make sure that the network switch is properly grounded. For information about  
regulatory requirements, see Regulatory Information, on page 2 .  
Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is  
used from a stereo signal).  
Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address  
(PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for  
audio out.  
SD card slot - A standard or high-capacity microSD card (not included) can be used for local  
recording with removable storage.  
NOTICE  
To prevent corruption of recordings, the SD card should be unmounted before removal. To  
unmount, go to Setup > System Options > Storage > SD Card and click Unmount.  
Control button - The control button is used for:  
Resetting the product to factory default settings. See page 14.  
Connecting to an AXIS Video Hosting System service or AXIS Internet Dynamic  
DNS Service. For more information about these services, see the User Manual.  
 
9
AXIS P7216 Video Encoder  
Power connector - 2-pin terminal block for power input. Use a limited power source (LPS) with  
either a rated output power limited to £100 W or a rated output current limited to £5 A.  
I/O terminal connector - Use in applications for e.g. motion detection, event triggering, time  
lapse recording and alarm notifications. In addition to an auxiliary power and a GND pin, the I/O  
terminal connector provides the interface to:  
Digital output – For connecting external devices such as relays and LEDs.  
Connected devices can be activated by the VAPIX® Application Programming  
Interface, output buttons on the Live View page or by an Action Rule. The  
output will show as active (shown under System Options > Ports & Devices) if  
the alarm device is activated.  
Digital input – An alarm input for connecting devices that can toggle between  
an open and closed circuit, for example: PIRs, door/window contacts, glass  
break detectors, etc. When a signal is received the state changes and the input  
becomes active (shown under System Options > Ports & Devices).  
RS-485/RS-422 connector - Two 2-pin terminal blocks for RS-485/RS-422 serial interface used to  
control auxiliary equipment, e.g. PTZ devices.  
Specifications  
Operating Conditions  
The casing of AXIS P7216 is not approved for outdoor use. The product may only be installed in  
indoor environments.  
Product  
Temperature  
Humidity  
AXIS P7216  
0 °C to 50 °C  
(32 °F to 122 °F)  
20-80% RH (non-condensing)  
Power Consumption  
Product  
Power supply  
AXIS PS-P power supply  
AXIS P7216  
 
10  
 
AXIS P7216 Video Encoder  
Connectors  
I/O terminal connector  
6-pin terminal block for:  
• Digital Input  
• Digital Output  
• Auxiliary power and ground  
(GND)  
Function  
Pin Notes  
Specifications  
1
2
GND  
Ground  
3.3 V DC  
Power  
Can be used to power auxiliary equipment.  
Note: This pin can only be used as power out.  
Max load = 250 mA  
0 to +40 V DC  
3–  
6
Configurable  
(Input or  
Output)  
Digital input — Connect to GND to activate,  
or leave floating (unconnected) to deactivate.  
Digital output — Internal connection  
to ground when activated, floating  
Max load =100 mA  
Max voltage = +40 V DC  
(unconnected) when deactivated. If used  
with an inductive load, e.g. a relay, a diode  
 
11  
AXIS P7216 Video Encoder  
must be connected in parallel with the load,  
for protection against voltage transients.  
A
B
I/O configured as input  
I/O configured as output  
Power connector  
DC power input  
2-pin terminal block for  
power input. Use a limited  
power source (LPS) with  
either a rated output power  
limited to £100 W or a rated  
output current limited to  
£5 A.  
Audio connector  
3.5 mm audio  
connectors (stereo)  
 
12  
AXIS P7216 Video Encoder  
Audio Input  
Audio Output  
1 Tip  
Microphone/Line in  
Line out (mono)  
2 Ring  
3 Sleeve  
Ground  
Ground  
RS-485/422 connector  
Two 2-pin terminal blocks for RS485/RS422 serial  
interface. The serial port can be configured to support:  
• Two-wire RS485 half duplex  
• Four-wire RS485 full duplex  
• Two-wire RS422 simplex  
• Four-wire RS422 full duplex point to point  
communication  
Function  
Pin  
Notes  
1
RS485/RS422 RX/TX  
A
(RX) For full duplex RS485/RS422  
(RX/TX) For half duplex RS485  
2
RS485/RS422 RX/TX  
B
3
4
RS485/RS422 TX A  
RS485/RS422 TX B  
(TX) For full duplex RS485/RS422  
Install the Hardware  
Mount the video encoder  
The AXIS P7216 is supplied with a mounting kit containing brackets. The unit can be mounted in  
a rack or on a wall.  
After removing the existing 4 screws, attach the mounting brackets to the video encoder at an  
angle suitable for installation in a standard 1U 19” rack, or on the wall.  
Mounting on a wall  
1. Position the video encoder against the wall with the brackets attached, and mark the  
four mounting holes for each bracket.  
2. Drill the four mounting holes.  
3. Attach the video encoder to the wall using appropriate screws.  
 
13  
 
AXIS P7216 Video Encoder  
Connect the cables  
1. Connect the video encoder to the network using a network cable RJ45 and/or a SFP cable.  
2. Optionally connect the external input/output devices.  
3. Optionally connect active speakers and/or external microphones.  
4. Connect the cameras to the video inputs.  
5. Connect the supplied indoor power adapter.  
6. Check that the indicator LEDs indicate the correct conditions. See LED Indicators, on  
page 8  
Auxiliary Connector  
The AXIS P7216 is equipped with an additional RJ45 network connector. The purpose with this  
connector is to simplify maintenance work on the AXIS P7216 that requires connection to a  
computer.  
Note  
The auxiliary connector should only be connected during maintenance work.  
Access the Product  
Use the tools provided on the Installation and Management Software CD to assign an IP address,  
set the password and access the video stream. This information is also available from the support  
Reset to Factory Default Settings  
Important  
Reset to factory default should be used with caution. A reset to factory default will reset  
all settings, including the IP address, to the factory default values.  
To reset the product to the factory default settings:  
Note  
To reset a single channel to the original factory default settings, use the button provided in  
that unit’s web interface.  
It is also possible to reset parameters to factory default via the web interface. Go to Setup  
> System Options > Maintenance.  
 
14  
   
AXIS P7216 Video Encoder  
Further Information  
The User Manual is available at www.axis.com  
Visit www.axis.com/techsup to check if there is updated firmware available for your network  
product. To see the currently installed firmware version, go to Setup > About.  
Visit Axis learning center www.axis.com/academy for useful trainings, webinars, tutorials and  
guides.  
Warranty Information  
For information about Axis’ product warranty and thereto related information, see  
 
15  
Installation Guide  
Ver. M1.8  
Date: May 2013  
Part No. 50452  
AXIS P7216 Video Encoder  
© Axis Communications AB, 2013  
 

3D Connexion Elliptical Trainer 137 40465 10 User Manual
Air King Vacuum Cleaner AKCVQZ80 User Manual
Airlink Network Card AGIGA32PCI User Manual
Alpine CD Player CDE 9842 User Manual
Altinex Stereo Amplifier DA1203RM User Manual
American Standard Plumbing Product 206490X User Manual
Atlona Car Amplifier AT HD V14 User Manual
Audiovox Satellite Radio XMCK30P User Manual
Bahco Trimmer P52 53 User Manual
Eureka Tents Tent Nergy Portable Canopy User Manual